+86 18912936653 |   info@chzom.com
You are here: Home » Blog » Blogs » Guidance Specification For Selection Of Bending Lass Mold

Guidance Specification For Selection Of Bending Lass Mold

Views: 140     Author: Site Editor     Publish Time: 2021-08-30      Origin: Site

4.1 Often used are 88 ° (R1), 30 ° / straight knife (R1/R0.5), 88 ° (R1), 88 ° (R1/R0.5) and flat mold, and special upper knife mold.

bending lass mold

4.2 Lower modes include: single / double V lower modes, angle of 30 ° and 88 °, V4,V 6,V7,V8,V10,V12,V16,V25 (mm)

4.3 Selection of the machete mold is generally based on the arrangement of the machete sequence after the review of the drawings.

4.4 Select top to the mode according to the angle:

When 4.4.1 processing angle is greater than or equal to 88 º, use upper knife mold (less than 88 °, e. g., knife, machete, machete, etc.).

  4.4.2 when machining angle is less than 88 º, a 30 ° upper blade mold (e. g., sharp knife / straight sharp knife) shall be selected.

  4.4.3 when needs to press the dead edge, fold into a sharp edge / sharp edge (usually 30 º), to flatten the dead edge.

  4.4.4 when plates exceed 3MM thick, avoid a sharp / straight knife to prevent damage to the tool.

  4.5 When processing U-shaped according to the appearance.


                                                                                                                                     

 a

 b

When b-a≧ 5mm, straight knife, straight knife, straight machete, machete can be selected.

At 1mm﹤b-a﹤ 5mm, a direct machete and a machete can be selected.

When b-a﹤ 1mm, a limitless is available.

Note: All 100mm﹥a, b﹥ 6mm are internal dimensions.

When Z-shaped, straight knife, sharp knife / straight knife, straight cutlass and curved lass are usually used.

Guidance specification for selection of bending lass mold

4.6 Selection of the lower model.

The 4.6.1 often selects the size of the V groove at 6 times the plate thickness.

4.6.2 selects the lower mode according to the Angle: when the Angle is greater than or equal to 88 º, the lower mode is 88 º, 30º; choose the lower mode is less than 88 º (measure the effective height of the upper blade mold: the upper blade mode on the upper blade clip force surface to the distance to the blade).

4.7 The following points should be noted when the upper and lower mold needs to be stitched together.

When 4.7.1, highly inconsistent mold cannot be mixed, so as not to cause bad Angle or even damage the knife mold, cause injury accidents.

When selecting the blade mold on the 4.7.2 edge door panel, the processing quality and easy access of the products shall be considered. Generally, the gap between both ends shall be considered if necessary at 3-6mm().

4.7.3 shall avoid using damaged mold processing products to avoid bad appearance, and check the blade straighness and flatness of the blade after installing the blade mold.

When 4.7.4 wants to avoid the position, it should pay attention to the appearance of quality problems such as stamping and Angle not in place.

4.8 Under abnormal circumstances, mold selection.

When 4.8.1 pressing line, a pressure resistant knife shall be selected for the upper mold, and the lower mold shall be flat and aligned with the upper / lower knife mold without steps.

When 4.8.2 processes U-shaped, when the opening size is 6MM small, it should be folded into the mouth larger than the second knife, then flatten the size, or form with special mold

If the inner R corner of 4.8.3 processing products is clearly required, the matching R corner upper blade mold shall be considered in advance in the selection of the upper blade mold, (if R0.3, R1, R4, R8 or R10).

4.8.4 When 6 MM is 2.0 thickness, 88 ºV8 downmold should be selected. When the plate thickness is 3.0 thickness should fold 10MM, 88 ºV12 downmold should be selected to prevent too small machining size and causing work skid and not machining.

4.8.5 processing of round steel must be selected with special knife mold and operated by special personnel.

4.9 When choosing upper / lower knife mold, try to prevent splicing printing and affect the appearance of the product.

4.10 When proofreading top / lower blade mold, apply 300mm mold proofreading. Use splicing small mold or less than 300mm blade mold proofreading. More than 1M, the length difference between upper / lower blade mold shall not be greater than 20%.

4.11 Before installing the tool mold, we must first check whether the limited travel of the machine tool is greater than the total height of the upper / lower tool mold, so as to prevent damage to the knife mold and cause industrial accidents.

4.12 Check the mold before correcting the mold, and check the locking degree again after proofreading.

4.13 It is not prohibited to put the knife mold on the equipment to prevent the mold from falling, damaging the mold or injuring people.

4.13 The blade mold shall be put into the specified mold frame and placed neatly.

4.14 Install two knife modes of different heights simultaneously on the equipment.

4.15 The section shall be regularly maintained and maintained by the knife mold and clearly marked.


Contact us

CHZOM is a leading and professional metal working machine manufacturer in China, which was established in 2010 and located in the cultural ancient city of Nanjing, Jiangsu Province. After 10 years development, it has been a famous and influential modern enterprise.

 

Quick Links

Product Category

Contact Us

 +86 18912936653
 +86 18912936653
 Shiqiu Industrial Park, Lishui District, Nanjing City,Jiangsu Province,China
 
Copyright © 2021 Nanjing Chzone Machine Tool Co.,Ltd. All rights reserved. Sitemap